Intech IN-uP4 - Universal Input Indicator

Manufacturer:

The IN-uP4 is a universal single input indicator, which makes interface with a wide range of sensors easy.

Part Number: IN-UP4

Select Required Model *

IN-uP4 No outputs
IN-uP4X 2 x Relay + 4-20mA outputs [+$137.00]

Programming Kit (required once)

Programming Kit for Intech XU Series Transmitters - XU-USB [+$127.00]

Back to Previous Page

Product Files

$390.00 ex GST

Qty:

i h

Overview
Specifications
Software

Description:

The IN-uP4 is a universal single input indicator, which makes interface with a wide range of sensors easy.
The IN-uP4 has a 4-digit LED display. An option to add two relay outputs (with two setpoint indicator LED’s), and one 4~20mA analogue output is available. The indicator (Rev 1) has a Universal Power Supply of 24~250Vac / 19.5~250Vdc.
Setup and calibration is simple, using ‘uP Configure’ software, with step-by-step instructions.

Features:

Universal Input with Indication.
Panel Mount.
Programmable via USB Port using uP Configure software and XU-USB (Rev 1) key.
Simple setup and calibration.
4-digit LED Display.
Option to add Two Relay Outputs (with two setpoint indicator LED’s), and One 4~20mA Analogue Output.
Universal Power Supply of 24~250Vac / 19.5~250Vdc.
Sensor Power Supply for powering external Transmitter.
IP65.

Ordering Information:

Code		Description
IN-uP4		Universal Input Indicator with No Outputs.
IN-uP4X		Universal Input Indicator with Two Relay Outputs plus One 4~20mA Analogue Output.

Universal Power Supply of 24~250Vac / 19.5~250Vdc.

Note: The IN-uP4 Universal Input Indicator is pre-programmed for RTD Pt100 input as standard.

To program the IN-uP4 requires the XU-USB (Rev 1) Programming Key:

XU-USB (Rev 1)

USB Programming Key for programming IN-uP4 using uP Configure Programming Software (version 1.5.7 or later).
Note: XU-USB must be (Rev 1) or later! Older versions will NOT connect with the IN-uP4.

(Same Key as used for programming XU Series transmitters, 2400-A16 / 2400-M-R, Z-2400-Sleeper, Z-2400-A2 Series
and uP4-Din.)

Input Specifications:
Excitation - Sensor Power Supply	+22Vdc ±10%, 25mA max.
Accuracy/Repeatability	0.05% of FSO.
Temperature Drift	30ppm/°C typical.
Voltage Input Specifications:
mV Range	-200mV~200mV.
V Range	0~1V, 0~10V, -10~30V, 0~300V.
Minimum Input resistance	1MΩ.
Linearity and Repeatability	<±0.02% FSO typical.
Response Time	100msec.
USB Programmable Zero	0~±99% of the Span.
USB Programmable Span	95% of FSO.
Current Input Specifications:
mA Range	0~20mA (4~20mA).
Input Resistance	10Ω.
Maximum Over-range	50mAdc Continuous.
Linearity and Repeatability	<±0.02% FSO typical.
Response Time	100msec.
USB Programmable Zero	0~±99% of the Span.
USB Programmable Span	1µA~24mAdc.
Thermocouple Input Specifications:
Thermocouple Types	B, E, J, K, N, R, S, T.
Input Impedance	1MΩ Minimum.
T/C Lead Resistance	100Ω Maximum.
Cold Junction Compensation	-10~70°C.
Accuracy	E, J, K, N, T <±1°C. B, R, S <±2°C.
Temperature Drift	E, J, K, N, T <±0.05°C. B, R, S <±0.2°C. CJC Error <±2°C.
Sensor Fail	Upscale or Downscale Selectable (Upscale Default).
Response Time	400msec.
USB Programmable Zero	0~±99% of the Span.
USB Programmable Span	Within Thermocouple Type limits.
RTD Input Specifications:
RTD Input	Pt100 or Pt1000 DIN 3-wire Type. (2-wire can be used with offset calibration.)
Sensor Current	0.3mA Nominal.
Lead Wire Resistance	Pt100: 10Ω/wire Maximum. Pt1000: 5Ω/wire Maximum. 0.02% FSO Offset Error per Ω of Lead Resistance. Sensor Fail Upscale or Downscale Selectable (Upscale Default).
Linearity (Pt100)	0.02% FSO for Span Inputs ≤200°C. 0.1% FSO for Span Inputs ≤300°C.
Linearity (Pt1000)	0.02% FSO for Span Inputs ≤200°C. 0.2% FSO for Span Inputs ≤300°C.
Response Time	400msec.
USB Programmable Zero	0~±99% of the Span.
USB Programmable Span	Within Thermocouple Type limits.
NTC Thermistor Input Specifications:
NTC Sensor Types	10K (Beta 3984) -55~125°C. 10K (Beta 3435) -50~110°C.
Response Time	100msec.
Pulse & Frequency Input Specifications:
Input Type	Open Contact: NPN, 24Vdc Max. PNP, 5Vdc Max.
Frequency Range	0~2000Hz.
Response Time	100msec.
Software Modes	General Frequency, Flow Rate or RPM.
Potentiometer Input Specifications:
Potentiometer input	3-wire.
Excitation voltage	Variable.
Field programmable zero	0~90% of span.
Potentiometer resistance	<1kΩ low pot; 1~4kΩ med pot; 4~20kΩ high pot.
Field programmable span	0.1~100%.
Linearity and repeatability	<±0.05% FSO typical.
Response time	100msec.
Output Specifications:	IN-uP4X only.
Analogue Output:	Isolated.
mA Range	4~20mA or 20~4mA.
Resolution	1µA.
Output Drive	600Ω at 12Vdc.
Relay Outputs:	2 Isolated Relays with LED indication on each output.
Functions	2 on Board Controllers can be used as Set Point (SV), Switching Differential, Auto/Manual, Manual Output Setting, Dual Action Control, Single Action Control, Heat/Cool, Cool Only, Heat Only.
Relay Ratings	250Vac, 3A Max.
General Specifications:
Power Supply:	24~250Vac / 19.5~250Vdc (47-63Hz, 6VA max).
Safety Compliance:
EMC Emissions	EN 61326.
EMC Immunity	EN 61326.
Safety	EN 61010-1.
General Specifications:
Accurate to	<±0.03% FSO typical.
Ambient drift	<±0.003%/°C FSO typical.
EMC Influence	<0.2% of full scale range.
Noise Immunity	125dB CMRR average (2.0KVdc limit).
Operating Humidity	5~85%RH max (non-condensing).
Operating Temperature	-10~50°C.
Storage Temperature	-20~60°C.
Indicator Housing:	IP65.
Dimensions	H=48mm, W=95mm, D=84mm. Allow 80mm minimum behind panel for connectors and wiring.
Panel Cutout	H=45mm, W=92mm.

Setup and calibration is simple, using ‘uP Configure’ software (version 1.5.23 or later), with step-by-step instructions.

Download uP Configure Software here

Description:

Features:

Universal Input with Indication.
Panel Mount.
Programmable via USB Port using uP Configure software and XU-USB (Rev 1) key.
Simple setup and calibration.
4-digit LED Display.
Option to add Two Relay Outputs (with two setpoint indicator LED’s), and One 4~20mA Analogue Output.
Universal Power Supply of 24~250Vac / 19.5~250Vdc.
Sensor Power Supply for powering external Transmitter.
IP65.

Ordering Information:

Code		Description
IN-uP4		Universal Input Indicator with No Outputs.
IN-uP4X		Universal Input Indicator with Two Relay Outputs plus One 4~20mA Analogue Output.

Universal Power Supply of 24~250Vac / 19.5~250Vdc.

Note: The IN-uP4 Universal Input Indicator is pre-programmed for RTD Pt100 input as standard.

To program the IN-uP4 requires the XU-USB (Rev 1) Programming Key:

XU-USB (Rev 1)

(Same Key as used for programming XU Series transmitters, 2400-A16 / 2400-M-R, Z-2400-Sleeper, Z-2400-A2 Series
and uP4-Din.)

Intech IN-uP4 - Universal Input Indicator

Description:

Features:

Ordering Information:

Download uP Configure Software here

Description:

Features:

Ordering Information:

Quality Guaranteed

Safe & Secure Payments

Quality Guaranteed

Intech IN-uP4 - Universal Input Indicator

Description:

Features:

Ordering Information:

Download uP Configure Software here

Description:

Features:

Ordering Information:

Intech Programming Kit for XU Series Transmitters - XU-USB

Intech uP4-Din - Universal Input Indicator, DIN Rail Mount

Quality Guaranteed

Safe & Secure Payments

Quality Guaranteed